Lincoln Aviator: Seatbelts / Seatbelt Reminder
WARNING: The system will only
provide protection when you use the
seatbelt correctly.
This system monitors all seating positions
and provides audio and graphic feedback.
This lamp illuminates and a
warning tone sounds if you do not
fasten your seatbelt when you
switch the ignition on. The lamp and tone
switch off when you fasten your seatbelt or
about one minute has elapsed.
When the initial warning expires for the
driver, more warnings are provided for the
driver and front outermost passenger. This
lamp illuminates and a warning tone sounds
if you or your front passenger do not fasten
the seatbelt buckle and the vehicle speed
exceeds 6 mph (9.7 km/h). To deactivate the
warning.
Note: To avoid inadvertent warnings, do not
place large objects on the front passenger
seat.
This lamp illuminates when you
switch the ignition on, identifying
the number of seating positions
with fastened buckles. It illuminates again
when a seating position changes from
unfastened to fastened.

This warning displays and a tone sounds if
an occupant unfastens the rear seatbelt
buckle or it becomes unfastened.
Note: If a rear seat is unoccupied, or an
occupant never fastens the seatbelt buckle
to begin with, the warning will not display.
Note: Front seating positions appear in this
warning display. Warnings for unfastened
front seatbelt buckles appear in the initial
warning lamp.
Seatbelt Status
To view the seatbelt status, use the
information display controls on the steering
wheel.


- Seatbelt fastened.
- Seatbelt not fastened.
- Seatbelt recently unfastened.
- Fault
Deactivating and Activating the Belt-Minder Feature - Front outermost
seats only
WARNING: While the system allows
you to deactivate it, this system is designed
to improve your chances of being safely
belted and surviving an accident. We
recommend you leave the system
activated for yourself and others who may
use the vehicle.
Note: The driver and front passenger
warnings switch on and off independently.
When you perform this procedure for one
seating position, do not buckle the other
position as this terminates the process.
Read Steps 1 - 4 before starting the
procedure.
Make sure that:
- You set the parking brake.
- The transmission is in park (P).
- The ignition is off.
- You close all vehicle doors.
- You unbuckle the driver and front
passenger seatbelts.
- Switch the ignition on. Do not start the
engine.
- Wait until the seatbelt warning lamp turns
off (about one minute). After Step 2, wait
an additional five seconds before
proceeding with Step 3. Once you start
Step 3, you must complete the procedure
within 60 seconds.
- For the seating position you are switching
off, buckle then unbuckle the seatbelt
three times at a moderate speed, ending
in the unbuckled state. After Step 3, the
seatbelt warning lamp turns on.
- When the seatbelt warning lamp is on,
buckle then unbuckle the seatbelt. After
Step 4, the seatbelt warning lamp flashes
for confirmation.
- This switches the feature off if it is
currently on.
- This switches the feature on if it is
currently off.
Inspect the vehicle seatbelts and child safety
seat systems periodically to make sure they
work properly and are not damaged. Inspect
the vehicle and child restraint seatbelts to
make sure there are no nicks, tears or cuts...
Other information:
Diagnostic Trouble Code (DTC) Chart
Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods (100-00 General Information, Description and Operation).
Diagnostic Trouble Code Chart
Module
DTC
Description
Action
BCM
B10C7:01
Interior Trunk Antenna: General Electrical Failure
GO to Pinpoint Test A
BCM
B10C9:01
Interior Front Antenna: General Electrical Failure
GO to Pinpoint Test A
BCM
B10D7:05
PATS Key: System Programming Faliure:
GO to Pinpoint Test C
BCM
B10D7:55
PATS Key: Not Configured:
GO to Pinpoint Test D
BCM
B10D8:00
PATS Key Less Than Minimum Programmed: No Sub Type Information:
GO to Pinpoint Test E
BCM
B10DA:51
PATS Target Identifier: Not Programmed:
GO to Pinpoint Test F
BCM
B1336:01
Left Front Door External Antenna: General Electrical Failure
GO to Pinpoint Test A
BCM
B1337:01
Right Front Door External Antenna: General Electrical Failure
GO to Pinpoint Test A
PCM
P161A:00
Incorrect Response from Immobilizer Control Module:General Electrical Failure
GO to Pinpoint Test G
PCM
P161B:00
Incorrect Response from Secondary Immobilizer Control Module:General Electrical Failure
GO to Pinpoint Test G
SOBDMC
P161A:00
Incorrect Response from Immobilizer Control Module:General Electrical Failure
GO to Pinpoint Test G
Symptom Chart
Symptom Chart: PATS
Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices...
Rear Window Wiper
Intermittent wipe.
Continuous wipe.
Rear window wiper off.
Depending on your vehicle, when you switch
on the front wipers and move the gearshift
lever to reverse (R), the rear intermittent wipe
may turn on.
Note: Make sure you switch the rear window
wiper off before entering a car wash...