Lincoln Aviator: Pedestrian Alert System / Diagnosis and Testing - Pedestrian Alert System

Diagnostic Trouble Code (DTC) Chart

Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices.
REFER to: Diagnostic Methods (100-00 General Information, Description and Operation).


  Diagnostic Trouble Code Chart


Module   DTC Description Action
  PACM B1A01:01 Speaker #1: General Electrical Failure   GO to Pinpoint Test C
  PACM B1A01:11 Speaker #1: Circuit Short To Ground   GO to Pinpoint Test C
  PACM B1A01:12 Speaker #1: Circuit Short To Battery   GO to Pinpoint Test D
  PACM B1A01:13 Speaker #1: Circuit Open   GO to Pinpoint Test D
  PACM B1A02:01 Speaker #2: General Electrical Failure   GO to Pinpoint Test C
  PACM B1A02:11 Speaker #2: Circuit Short To Ground   GO to Pinpoint Test C
  PACM B1A02:12 Speaker #2: Circuit Short To Battery   GO to Pinpoint Test D
  PACM B1A02:13 Speaker #2: Circuit Open   GO to Pinpoint Test D
  PACM U0100:00 Lost Communication With ECM/PCM "A": No Sub Type Information   GO to Pinpoint Test E
  PACM U0140:00 Lost Communication With Body Control Module: No Sub Type Information   GO to Pinpoint Test F
  PACM U0422:00 Invalid Data Received From Body Control Module: No Sub Type Information   GO to Pinpoint Test G
  PACM U201A:51 Control Module Main Calibration Data: Not Programmed   GO to Pinpoint Test H
  PACM U2101:00 Control Module Configuration Incompatible: No Sub Type Information   GO to Pinpoint Test H
  PACM U3000:41 Control Module: General Checksum Failure   GO to Pinpoint Test I
  PACM U3000:42 Control Module: General Memory Failure   GO to Pinpoint Test I
  PACM U3000:96 Control Module: Component Internal Failure   GO to Pinpoint Test I
  PACM U3003:16 Battery Voltage: Circuit Voltage Below Threshold   GO to Pinpoint Test J
  PACM U3003:17 Battery Voltage: Circuit Voltage Above Threshold   GO to Pinpoint Test K

Symptom Chart

Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices.
REFER to: Diagnostic Methods (100-00 General Information, Description and Operation).


  Symptom Chart


Condition Actions
The pedestrian alert system is inoperative   GO to Pinpoint Test A
A sounder is distorted   GO to Pinpoint Test B
Poor sounder volume   GO to Pinpoint Test A

Pinpoint Tests


PINPOINT TEST A : THE PEDESTRIAN ALERT SYSTEM IS INOPERATIVE

Normal Operation and Fault Conditions

See Pedestrian Alert System description. REFER to: Pedestrian Alert System - System Operation and Component Description (413-22 Pedestrian Alert System, Description and Operation).

The PACM receives a hot at all times voltage from the BCM. The PACM receives the ignition status message for the RUN/START or ACC input from the BCM through the GWM over the HS-CAN3.

Possible Sources

  • Fuse
  • Communication concern
  • PACM
A1 PERFORM THE NETWORK TEST FOR ALL MODULES
  • Using a diagnostic scan tool, perform a network test.

Do all equipped modules pass the network test?
Yes GO to A2
No
REFER to: Communications Network (418-00 Module Communications Network, Diagnosis and Testing).

A2 PERFORM THE PACM (PEDESTRIAN ALERT CONTROL MODULE) MODULE SELF-TEST
  • Ignition ON.
  • Using a diagnostic scan tool, perform the PACM module self-test.
  • Check for recorded Diagnostic Trouble Codes (DTCs) from the PACM module self-test.

Are any Diagnostic Trouble Codes (DTCs) recorded?
Yes REFER to DTC Chart: PACM in this section.
No GO to A3

A3 CHECK THE SOUNDER OPERATION
  • Install a known good sounder.
    REFER to: Pedestrian Alert System Speaker (413-22 Pedestrian Alert System, Removal and Installation).
  • NOTE: Make sure the vehicle is operating in electric mode (engine not running). Operate the vehicle in a forward range between 0-30 km/h (0-8 mph) and verify whether the pedestrain alert system sounder operates.

Does the pedestrian alert system sounder operate?
Yes INSTALL a new sounder.
REFER to: Pedestrian Alert System Speaker (413-22 Pedestrian Alert System, Removal and Installation).
No REINSTALL the original sounder. INSTALL a new PACM.
REFER to: Pedestrian Alert Control Module (PACM) (413-22 Pedestrian Alert System, Removal and Installation).

PINPOINT TEST B : A SOUNDER IS DISTORTED

Normal Operation and Fault Conditions

The front and rear sounder are controlled by the PACM. Distorted sound is often caused by either debris surrounding the sounder area or a sounder.

Possible Sources

  • Debris surrounding the sounder
  • Front sounder
  • Rear sounder
B1 INSPECT THE SOUNDER
  • INSPECT and CLEAR any debris around the sounder.

Is any debris present around the sounder?
Yes CLEAR the debris from the sounder area.
No INSTALL a new sounder.
REFER to: Pedestrian Alert System Speaker (413-22 Pedestrian Alert System, Removal and Installation).

PINPOINT TEST C : B1A01:01, B1A01:11, B1A02:01, B1A02:11

Refer to Wiring Diagrams Cell 146 for schematic and connector information.

Normal Operation and Fault Conditions

The PACM controls the front and rear sounder output on hardwired circuitry and sets Diagnostic Trouble Codes (DTCs) when a circuit or sounder fault is detected.

DTC Fault Trigger Conditions

DTC Description Fault Trigger Condition
PACM B1A01:01 Speaker #1: General Electrical Failure An on-demand DTC that sets when the PACM detects the front sounder signal and return circuits are shorted together.
PACM B1A01:11 Speaker #1: Circuit Short To Ground An on-demand DTC that sets when the PACM detects the front sounder signal or return circuit is shorted to ground.
PACM B1A02:01 Speaker #2: General Electrical Failure An on-demand DTC that sets when the PACM detects the rear sounder signal and return circuits are shorted together.
PACM B1A02:11 Speaker #2: Circuit Short To Ground An on-demand DTC that sets when the PACM detects the rear sounder signal or return circuit is shorted to ground.

Possible Sources

  • Wiring, terminals or connectors
  • Front sounder
  • Rear sounder
  • PACM

Visual Inspection and Pre-checks

  • Inspect the sounder connector for corrosion (install new connector or terminals – clean module pins)
  • Inspect the sounder connector for damaged or bent pins – install new terminals/pins
  • Inspect the sounder connector for pushed-out pins – install new pins as necessary
C1 PERFORM THE PACM (PEDESTRIAN ALERT CONTROL MODULE) MODULE SELF-TEST
  • Ignition ON.
  • Using a diagnostic scan tool, perform the PACM module self-test.
  • Check for recorded Diagnostic Trouble Codes (DTCs) from the PACM module self-test.

Is DTC B1A01:01 or B1A02:01 recorded?
Yes GO to C2
No GO to C4

C2 CHECK THE SOUNDER FOR AN INTERNAL SHORT
  • Ignition OFF.
  • Disconnect Front Sounder C1945 (DTC B1A01:01).
  • Disconnect Rear Sounder C4526 (DTC B1A02:01).
  • Ignition ON.
  • Using a diagnostic scan tool, perform the PACM module self-test.
  • NOTE: DTC B1A01:01 or B1A02:01 can also be present when carrying out this step and should be disregarded at this time. Check for recorded Diagnostic Trouble Codes (DTCs) from the PACM module self-test.

Is DTC B1A01:13 or B1A02:13 recorded?
Yes INSTALL a new sounder. REFER to Removal and Installation/Pedestrian Alert System Speaker.
No GO to C3

C3 CHECK THE SOUNDER SIGNAL AND RETURN CIRCUIT FOR A SHORT TOGETHER
  • Ignition OFF.
  • Disconnect PACM C4525 .
  • Measure:
    Click to display connectors

      Front Sounder (DTC B1A01:01)


    Lead 1 Measurement / Action Lead 2
      C4525-9   C4525-8

    Click to display connectors

      Rear Sounder (DTC B1A02:01)


    Lead 1 Measurement / Action Lead 2
      C4525-11   C4525-10

Is the resistance greater than 10,000 ohms?
Yes GO to C6
No REPAIR the circuits.

C4 CHECK THE SOUNDER SIGNAL CIRCUIT FOR A SHORT TO GROUND
  • Ignition OFF.
  • Disconnect PACM C4525 .
  • Disconnect Front Sounder C1945 (DTC B1A01:11).
  • Disconnect Rear Sounder C4526 (DTC B1A02:11).
  • Measure:
    Click to display connectors

      Front Sounder (DTC B1A01:11)


    Lead 1 Measurement / Action Lead 2
      C4525-9   Ground

    Click to display connectors

      Rear Sounder (DTC B1A02:11)


    Lead 1 Measurement / Action Lead 2
      C4525-11   Ground

Is the resistance greater than 10,000 ohms?
Yes GO to C5
No REPAIR the circuit.

C5 CHECK THE SOUNDER RETURN CIRCUIT FOR A SHORT TO GROUND
  • Measure:
    Click to display connectors

      Front Sounder (DTC B1A01:11)


    Lead 1 Measurement / Action Lead 2
      C4525-8   Ground

    Click to display connectors

      Rear Sounder (DTC B1A02:11)


    Lead 1 Measurement / Action Lead 2
      C4525-10   Ground

Is the resistance greater than 10,000 ohms?
Yes GO to C6
No REPAIR the circuit.

C6 CHECK FOR CORRECT PACM (PEDESTRIAN ALERT CONTROL MODULE) OPERATION
  • Ignition OFF.
  • Disconnect and inspect the PACM and connector.
  • Repair:
    • corrosion (install new connector or terminals – clean module pins)
    • damaged or bent pins – install new terminals/pins
    • pushed-out pins – install new pins as necessary
  • Reconnect the PACM connector. Make sure it seats and latches correctly.
  • Operate the system and determine if the concern is still present.

Is the concern still present?
Yes CHECK OASIS for any applicable service articles: TSB, GSB, SSM or FSA. If a service article exists for this concern, DISCONTINUE this test and FOLLOW the service article instructions. If no service articles address this concern, INSTALL a new PACM.
REFER to: Pedestrian Alert Control Module (PACM) (413-22 Pedestrian Alert System, Removal and Installation).
No The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.

PINPOINT TEST D : B1A01:12, B1A01:13, B1A02:12, B1A02:13

Refer to Wiring Diagrams Cell 146 for schematic and connector information.

Normal Operation and Fault Conditions

The PACM controls the front and rear sounder output on hardwired circuitry and sets Diagnostic Trouble Codes (DTCs) when a circuit or sounder fault is detected.

DTC Fault Trigger Conditions

DTC Description Fault Trigger Condition
PACM B1A01:12 Speaker #1: Circuit Short To Battery An on-demand DTC that sets when the PACM detects the front sounder signal or return circuits are shorted to voltage.
PACM B1A01:13 Speaker #1: Circuit Open An on-demand DTC that sets when the PACM detects the front sounder signal or return circuit is open.
PACM B1A02:12 Speaker #2: Circuit Short To Battery An on-demand DTC that sets when the PACM detects the rear sounder signal or return circuits are shorted to voltage.
PACM B1A02:13 Speaker #2: Circuit Open An on-demand DTC that sets when the PACM detects the rear sounder signal or return circuit is open.

Possible Sources

  • Wiring, terminals or connectors
  • Front sounder
  • Rear sounder
  • PACM

Visual Inspection and Pre-checks

  • Inspect the sounder connector for corrosion (install new connector or terminals – clean module pins)
  • Inspect the sounder connector for damaged or bent pins – install new terminals/pins
  • Inspect the sounder connector for pushed-out pins – install new pins as necessary
D1 PERFORM THE PACM (PEDESTRIAN ALERT CONTROL MODULE) MODULE SELF-TEST
  • Ignition ON.
  • Using a diagnostic scan tool, perform the PACM module self-test.
  • Check for recorded Diagnostic Trouble Codes (DTCs) from the PACM module self-test.

Is DTC B1A01:12 or B1A02:12 recorded?
Yes GO to D2
No GO to D4

D2 CHECK FOR A SHORT TO VOLTAGE AT THE SOUNDER
  • Ignition OFF.
  • Disconnect PACM C4525 .
  • Ignition ON.
  • Measure:
    Click to display connectors

      Front Sounder (DTC B1A01:12)


    Lead 1 Measurement / Action Lead 2
      C4525-9   Ground

    Click to display connectors

      Rear Sounder (DTC B1A02:12)


    Lead 1 Measurement / Action Lead 2
      C4525-11   Ground

Is any voltage present?
Yes GO to D3
No GO to D7

D3 CHECK FOR A SHORT TO VOLTAGE WITH THE SOUNDER DISCONNECTED
  • Ignition OFF.
  • Disconnect Front Sounder C1945 (DTC B1A01:12).
  • Disconnect Rear Sounder C4526 (DTC B1A02:12).
  • Measure:
    Click to display connectors

      Front Sounder (DTC B1A01:12)


    Lead 1 Measurement / Action Lead 2
      C4525-9   Ground

    Click to display connectors

      Rear Sounder (DTC B1A02:12)


    Lead 1 Measurement / Action Lead 2
      C4525-11   Ground
  • Ignition ON.

Is any voltage present?
Yes REPAIR the signal circuit.
No REPAIR the return circuit.

D4 CHECK THE SOUNDER FOR AN OPEN
  • Ignition OFF.
  • Disconnect Front Sounder C1945 (DTC B1A01:13).
  • Disconnect Rear Sounder C4526 (DTC B1A02:13).
  • Connect a fused jumper wire:
    Click to display connectors

      Front Sounder (DTC B1A01:13)


    Lead 1 Measurement / Action Lead 2
      C1945-1   C1945-2

    Click to display connectors

      Rear Sounder (DTC B1A02:13)


    Lead 1 Measurement / Action Lead 2
      C4526-1   C4526-2
  • Ignition ON.
  • Using a diagnostic scan tool, perform the PACM module self-test.
  • NOTE: DTC B1A01:13 or B1A02:13 can also be present when carrying out this step and should be disregarded at this time. Check for recorded Diagnostic Trouble Codes (DTCs) from the PACM module self-test.

Is DTC B1A01:11 or B1A02:11 recorded?
Yes REMOVE the fused jumper wire.
REFER to: Pedestrian Alert System Speaker (413-22 Pedestrian Alert System, Removal and Installation).
No REMOVE the fused jumper wire. GO to D5

D5 CHECK THE SOUNDER SIGNAL CIRCUIT FOR AN OPEN
  • Ignition OFF.
  • Disconnect PACM C4525 .
  • Measure:
    Click to display connectors

      Front Sounder (DTC B1A01:13)


    Lead 1 Measurement / Action Lead 2
      C4525-9   C1945-1

    Click to display connectors

      Rear Sounder (DTC B1A02:13)


    Lead 1 Measurement / Action Lead 2
      C4525-11   C4526-1

Is the resistance less than 3 ohms?
Yes GO to D6
No REPAIR the circuit in question.

D6 CHECK THE SOUNDER RETURN CIRCUIT FOR AN OPEN
  • Measure:
    Click to display connectors

      Front Sounder (DTC B1A01:13)


    Lead 1 Measurement / Action Lead 2
      C4525-8   C1945-2

    Click to display connectors

      Rear Sounder (DTC B1A02:13)


    Lead 1 Measurement / Action Lead 2
      C4525-10   C4526-2

Is the resistance less than 3 ohms?
Yes GO to D7
No REPAIR the circuit in question.

D7 CHECK FOR CORRECT PACM (PEDESTRIAN ALERT CONTROL MODULE) OPERATION
  • Ignition OFF.
  • Disconnect and inspect the PACM and connector.
  • Repair:
    • corrosion (install new connector or terminals – clean module pins)
    • damaged or bent pins – install new terminals/pins
    • pushed-out pins – install new pins as necessary
  • Reconnect the PACM connector. Make sure it seats and latches correctly.
  • Operate the system and determine if the concern is still present.

Is the concern still present?
Yes CHECK OASIS for any applicable service articles: TSB, GSB, SSM or FSA. If a service article exists for this concern, DISCONTINUE this test and FOLLOW the service article instructions. If no service articles address this concern, INSTALL a new PACM.
REFER to: Pedestrian Alert Control Module (PACM) (413-22 Pedestrian Alert System, Removal and Installation).
No The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.

PINPOINT TEST E : U0100:00

Normal Operation and Fault Conditions

The PACM communicates with the PCM over the HS-CAN1.

DTC Fault Trigger Conditions

DTC Description Fault Trigger Condition
PACM U0100:00 Lost Communication With ECM/PCM "A": No Sub Type Information Sets on-demand and in continuous memory in the PACM if data messages received from the PCM through the GWM are missing for 5 seconds or longer.

Possible Sources

  • Communication concern
  • PCM
  • PACM concern
E1 CHECK THE PACM (PEDESTRIAN ALERT CONTROL MODULE) CONTINUOUS MEMORY DIAGNOSTIC TROUBLE CODES (CMDTCS)
  • Ignition ON.
  • Using a diagnostic scan tool, perform the PACM self-test.
  • Clear the Diagnostic Trouble Codes (DTCs).
  • Wait 10 seconds.
  • Repeat the PACM self-test.

Are any non-network Diagnostic Trouble Codes (DTCs) present?
Yes DIAGNOSE all non-network Diagnostic Trouble Codes (DTCs). REFER to DTC Chart: PACM Module in this section.
No GO to E2

E2 PERFORM THE PCM (POWERTRAIN CONTROL MODULE) KOEO (KEY ON, ENGINE OFF) SELF-TEST
  • Using a diagnostic scan tool, perform the PCM KOEO self-test.

Are any non-network Diagnostic Trouble Codes (DTCs) present?
Yes DIAGNOSE all non-network Diagnostic Trouble Codes (DTCs). REFER to the Master DTC Chart.
No GO to E3

E3 RECHECK THE PACM (PEDESTRIAN ALERT CONTROL MODULE) DIAGNOSTIC TROUBLE CODES (DTCS)
  • Using a diagnostic scan tool, clear the PACM Diagnostic Trouble Codes (DTCs).
  • Ignition OFF.
  • Ignition ON.
  • Wait 10 seconds.
  • Using a diagnostic scan tool, perform the continuous memory self-test.
  • Check the PACM Diagnostic Trouble Codes (DTCs).

Is DTC U0100:00 still present?
Yes GO to E4
No The system is operating correctly at this time. The DTC may have set due to high network traffic or an intermittent fault condition.

E4 CHECK FOR OTHER CAUSES OF COMMUNICATION NETWORK CONCERN

NOTE: If new modules were installed prior to the DTC being set, the module configuration can be incorrectly set during the PMI or the PMI may not have been carried out.

  • CHECK the vehicle service history for recent service actions related to the PCM or PACM. If recent service history is found:
    • verify correct replacement module was installed
      • vehicle parts build may be used to verify correct part fitment
    • verify the configuration of replacement module was correct
      • re-configure module using as-built data if prior configuration is suspect
    • verify the module was not obtained from a like vehicle and installed into customer vehicle
      • return the swapped module to source vehicle and obtain new replacement module
  • Operate the system and determine if the observable symptom is still present.

Is the observable symptom still present?
Yes GO to E5
No The system is operating correctly at this time. The concern may have been due to incorrect parts replacement procedures or incorrect module configuration.

E5 CHECK FOR CORRECT PCM (POWERTRAIN CONTROL MODULE) OPERATION
  • Ignition OFF.
  • Disconnect and inspect the PCM.
  • Repair:
    • corrosion (install new connector or terminals – clean module pins)
    • damaged or bent pins – install new terminals/pins
    • pushed-out pins – install new pins as necessary
  • Reconnect the PCM connectors. Make sure they seat and latch correctly.
  • Operate the system and determine if the concern is still present.

Is the concern still present?
Yes CHECK OASIS for any applicable service articles: TSB, GSB, SSM or FSA. If a service article exists for this concern, DISCONTINUE this test and FOLLOW the service article instructions. If no service articles address this concern,
   Click here to access Guided Routine (PCM). Internet Explorer version 11 or greater is required to perform this Pinpoint Test.
No The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.

PINPOINT TEST F : U0140:00

Normal Operation and Fault Conditions

The PACM communicates with the BCM over the HS-CAN1.

DTC Fault Trigger Conditions

DTC Description Fault Trigger Condition
PACM U0140:00 Lost Communication With Body Control Module: No Sub Type Information Sets on-demand and in continuous memory in the PACM module if data messages received from the BCM are missing for 5 seconds or longer.

Possible Sources

  • Communication concern
  • BCM
  • PACM concern
F1 VERIFY THE CUSTOMER CONCERN
  • Ignition ON.
  • Verify there is an observable symptom present.

Is an observable symptom present?
Yes GO to F2
No CLEAR the DTC. The system is operating normally at this time. The DTC may have been set due to high network traffic or an intermittent fault condition.

F2 CHECK THE COMMUNICATION NETWORK
  • Using a diagnostic scan tool, perform the network test.

Does the BCM pass the network test?
Yes GO to F3
No
REFER to: Communications Network (418-00 Module Communications Network, Diagnosis and Testing).

F3 PERFORM THE PACM (PEDESTRIAN ALERT CONTROL MODULE) SELF-TEST
  • Using a diagnostic scan tool, perform the PACM self-test.

Are any non-network Diagnostic Trouble Codes (DTCs) present?
Yes REFER to DTC Chart: PACM in this section.
No GO to F4

F4 PERFORM THE BCM (BODY CONTROL MODULE) SELF-TEST
  • Using a diagnostic scan tool, perform the BCM self-test.

Are any non-network Diagnostic Trouble Codes (DTCs) present?
Yes REFER to the Master DTC Chart.
No GO to F5

F5 RECHECK THE PACM (PEDESTRIAN ALERT CONTROL MODULE) DIAGNOSTIC TROUBLE CODES (DTCS)
  • Using a diagnostic scan tool, clear the PACM Diagnostic Trouble Codes (DTCs).
  • Ignition OFF.
  • Ignition ON.
  • Wait 10 seconds.
  • Using a diagnostic scan tool, perform the continuous memory self-test.
  • Check the PACM Diagnostic Trouble Codes (DTCs).

Is DTC U0140:00 still present?
Yes GO to F6
No The system is operating correctly at this time. The DTC may have been set due to high network traffic or an intermittent fault condition.

F6 CHECK FOR OTHER CAUSES OF COMMUNICATION NETWORK CONCERN

NOTE: If new modules were installed prior to the DTC being set, the module configuration may be incorrectly set during the PMI, or the PMI may not have been carried out.

  • CHECK the vehicle service history for recent service actions related to the BCM or PACM module. If recent service history is found:
    • verify correct replacement module was installed
      • vehicle parts build may be used to verify correct part fitment
    • verify the configuration of replacement module was correct
      • re-configure module using as-built data if prior configuration is suspect
    • verify the module was not obtained from a like vehicle and installed into customer vehicle
      • return the swapped module to source vehicle and obtain new replacement module
  • Operate the system and determine if the observable symptom is still present.

Is the observable symptom still present?
Yes GO to F7
No The system is operating correctly at this time. The concern may have been due to incorrect parts replacement procedures or incorrect module configuration.

F7 CHECK FOR CORRECT BCM (BODY CONTROL MODULE) OPERATION
  • Ignition OFF.
  • Disconnect and inspect the BCM connectors.
  • Repair:
    • corrosion (install new connector or terminals – clean module pins)
    • damaged or bent pins – install new terminals/pins
    • pushed-out pins – install new pins as necessary
  • Reconnect the BCM connectors. Make sure they seat and latch correctly.
  • Operate the system and determine if the concern is still present.

Is the concern still present?
Yes CHECK OASIS for any applicable service articles: TSB, GSB, SSM or FSA. If a service article exists for this concern, DISCONTINUE this test and FOLLOW the service article instructions. If no service articles address this concern, INSTALL a new BCM.
REFER to: Body Control Module (BCM) (419-10 Multifunction Electronic Modules, Removal and Installation).
No The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.

PINPOINT TEST G : U0422:00

Normal Operation and Fault Conditions

The PACM receives ignition state data from the BCM over the HS-CAN1.

DTC Fault Trigger Conditions

DTC Description Fault Trigger Condition
PACM U0422:00 Invalid Data Received From Body Control Module: No Sub Type Information This DTC sets when the PACM receives invalid ignition data from the BCM.

Possible Sources

  • BCM concern
G1 CHECK THE FOR NON-NETWORK DIAGNOSTIC TROUBLE CODES SET IN THE BCM (BODY CONTROL MODULE)
  • Ignition ON.
  • Using a diagnostic scan tool, clear the Diagnostic Trouble Codes (DTCs).
  • Wait 10 seconds.
  • Using a diagnostic scan tool, perform the BCM self-test.

Are any non-network Diagnostic Trouble Codes (DTCs) present?
Yes REFER to the Master DTC Chart.
No DIAGNOSE the observable symptom.

PINPOINT TEST H : U201A:51, U2101:00

Normal Operation and Fault Conditions

The PACM sets Diagnostic Trouble Codes when PMI isn't completed or if incorrect module parameters are set.

DTC Fault Trigger Conditions

DTC Description Fault Trigger Condition
PACM U201A:51 Control Module Main Calibration Data: Not Programmed This DTC sets in the PACM due to incomplete or incorrect PMI procedures.
PACM U2101:00 Control Module Configuration Incompatible: No Sub Type Information This DTC sets in the PACM due to incomplete or incorrect PMI procedures.

Possible Sources

  • PACM programming concern
H1 CHECK FOR RECENT SERVICE HISTORY
  • Ignition ON.
  • Check the vehicle service history for recent service actions related to PACM.

Have there been any recent service actions related to the PACM?
Yes PROGRAM the PACM using as-built data.
REFER to: Module Programming (418-01 Module Configuration, General Procedures).
No INSTALL a new PACM for failure to retain module programming.
REFER to: Pedestrian Alert Control Module (PACM) (413-22 Pedestrian Alert System, Removal and Installation).

PINPOINT TEST I : U3000:41, U3000:42, U3000:96

Normal Operation and Fault Conditions

The PACM monitors internal memory status and memory programming and sets Diagnostic Trouble Codes when a concern is present.

DTC Fault Trigger Conditions

DTC Description Fault Trigger Condition
PACM U3000:41 Control Module: General Checksum Failure This DTC sets when an internal programming checksum concern exists in the PACM.
PACM U3000:42 Control Module: General Memory Failure This DTC sets when an internal memory concern exists in the PACM.
PACM U3000:96 Control Module: Component Internal Failure This DTC sets when an internal concern exists in the PACM.

Possible Sources

  • Internal PACM concern
I1 RECHECK THE PACM (PEDESTRIAN ALERT CONTROL MODULE) DIAGNOSTIC TROUBLE CODES (DTCS)
  • Ignition ON.
  • Using a diagnostic scan tool, clear the Diagnostic Trouble Codes (DTCs).
  • Wait 10 seconds.
  • Using a diagnostic scan tool, perform the PACM self-test.

Is DTC U3000:41, U3000:42 or U3000:96 still present?
Yes INSTALL a new PACM.
REFER to: Pedestrian Alert Control Module (PACM) (413-22 Pedestrian Alert System, Removal and Installation).
No The PACM is operating correctly at this time. The concern may have been caused by a temporary low battery condition.

PINPOINT TEST J : U3003:16

Refer to Wiring Diagrams Cell 146 for schematic and connector information.

Normal Operation and Fault Conditions

The PACM monitors battery voltage and sets a DTC when operating voltage is low.

DTC Fault Trigger Conditions

DTC Description Fault Trigger Condition
PACM U3003:16 Battery Voltage: Circuit Voltage Below Threshold Sets in the PACM module in continuous memory if the PACM module detects battery voltage below 9 volts on the voltage supply circuit for 50 milliseconds or longer.

Possible Sources

  • Wiring, terminals or connectors
  • High circuit resistance
  • Charging system concern
  • PACM
J1 RECHECK THE PACM (PEDESTRIAN ALERT CONTROL MODULE) DIAGNOSTIC TROUBLE CODES (DTCS)
  • Ignition ON.
  • Using a diagnostic scan tool, clear the Diagnostic Trouble Codes (DTCs).
  • Wait 10 seconds.
  • Using a diagnostic scan tool, perform the PACM self-test.

Is DTC U3003:16 still present?
Yes GO to J2
No The system is operating correctly at this time. The DTC may have been set due to a previous low battery voltage condition.

J2 CHECK FOR CHARGING SYSTEM DIAGNOSTIC TROUBLE CODES (DTCS) IN THE BCM (BODY CONTROL MODULE)
  • Using a diagnostic scan tool, perform the BCM self-test.

Are any charging system Diagnostic Trouble Codes (DTCs) recorded?
Yes REFER to the Master DTC Chart.
No GO to J3

J3 CHECK THE BATTERY CONDITION AND STATE OF CHARGE
  • Check the battery condition and verify the battery is fully charged.
    REFER to: Battery (414-01 Battery, Mounting and Cables, Diagnosis and Testing).

Is the battery OK and fully charged?
Yes GO to J4
No If the battery is discharged, DIAGNOSE the cause of the low battery condition.
REFER to: Battery (414-01 Battery, Mounting and Cables, Diagnosis and Testing). If the battery condition fails, INSTALL a new battery.
REFER to: Battery (414-01 Battery, Mounting and Cables, Removal and Installation).

J4 CHECK THE PACM (PEDESTRIAN ALERT CONTROL MODULE) VOLTAGE PID (PARAMETER IDENTIFICATION)
  • Measure and record the voltage at the battery.
  • Using a diagnostic scan tool, view the PACM Parameter Identifications (PIDs).
  • Monitor the PACM voltage (MODULE_VOLT) PID

Is the voltage within 0.2 volt of the recorded battery voltage?
Yes GO to J7
No GO to J5

J5 CHECK THE PACM (PEDESTRIAN ALERT CONTROL MODULE) VOLTAGE SUPPLY
  • Ignition OFF.
  • Disconnect PACM C4525 .
  • Ignition ON.
  • Measure:
    Click to display connectors
    Positive Lead Measurement / Action Negative Lead
      C4525-6   Ground

Is the voltage greater than 11 volts?
Yes GO to J6
No REPAIR the circuit for high circuit resistance.

J6 CHECK THE PACM (PEDESTRIAN ALERT CONTROL MODULE) GROUND
  • Measure:
    Click to display connectors
    Positive Lead Measurement / Action Negative Lead
      C4525-6   C4525-1

Is the voltage greater than 11 volts?
Yes GO to J7
No REPAIR the circuit for high circuit resistance.

J7 CHECK FOR CORRECT PACM (PEDESTRIAN ALERT CONTROL MODULE) OPERATION
  • Ignition OFF.
  • Disconnect and inspect the PACM connector.
  • Repair:
    • corrosion (install new connector or terminals – clean module pins)
    • damaged or bent pins – install new terminals/pins
    • pushed-out pins – install new pins as necessary
  • Reconnect the PACM connector. Make sure it seats and latches correctly.
  • Operate the system and determine if the concern is still present.

Is the concern still present?
Yes CHECK OASIS for any applicable service articles: TSB, GSB, SSM or FSA. If a service article exists for this concern, DISCONTINUE this test and FOLLOW the service article instructions. If no service articles address this concern, INSTALL a new PACM.
REFER to: Pedestrian Alert Control Module (PACM) (413-22 Pedestrian Alert System, Removal and Installation).
No The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.

PINPOINT TEST K : U3003:17

Normal Operation and Fault Conditions

The PACM monitors battery voltage and sets a DTC when operating voltage is high.

DTC Fault Trigger Conditions

DTC Description Fault Trigger Condition
PACM U3003:17 Battery Voltage: Circuit Voltage Above Threshold Sets in the PACM in continuous memory if the PACM detects battery voltage above 16 volts on the voltage supply circuit for 50 milliseconds or longer.

Possible Sources

  • Charging system concern
  • PACM
NOTE: DTC U3003:17 may be stored in the module memory due to past battery charging or vehicle jump starting events.
K1 CHECK FOR OVERCHARGING DIAGNOSTIC TROUBLE CODES (DTCS) SET IN OTHER MODULES
  • Ignition ON.
  • Using a diagnostic scan tool, perform self-test on all modules.
  • Retrieve the continuous memory DTCs from all modules.

Are any high voltage Diagnostic Trouble Codes (DTCs) set in more than one module?
Yes DIAGNOSE the overcharging condition. REFER to the appropriate 414-00 section.
No GO to K2

K2 CHECK THE BATTERY VOLTAGE
  • Turn off all interior/exterior lights and accessories.
  • Start and run the engine at approximately 2,000 rpm for 3 minutes while monitoring the battery voltage.

Does the battery voltage rise to 15.5 volts or higher?
Yes DIAGNOSE the overcharging condition. REFER to the appropriate 414-00 section.
No GO to K3

K3 RECHECK FOR DTC (DIAGNOSTIC TROUBLE CODE) U3003:17
  • Ignition OFF.
  • Ignition ON.
  • Using a diagnostic scan tool, clear the continuous memory DTCs.
  • Carry out the IPC self-test.

Is DTC U3003:17 present?
Yes INSTALL a new PACM.
REFER to: Pedestrian Alert Control Module (PACM) (413-22 Pedestrian Alert System, Removal and Installation).
No The system is operating correctly at this time. The DTC may have been set previously during battery charging or while jump starting the vehicle.


    Description and Operation - Pedestrian Alert System - System Operation and Component Description

    System Operation System Diagram Item Description 1 PACM 2 PCM 3 IPC 4 Rear sounder 5 BCM 6 SOBDMC 7 Front sounder Network Message Charts   Module Network Input Messages - PACM Broadcast Message Originating Module Message Purpose Factory mode   BCM Controls the pedestrian alert system based on the vehicle build status set in factory mode...

    Removal and Installation - Pedestrian Alert Control Module (PACM)

    Special Tool(s) / General Equipment Interior Trim Remover Removal Remove the luggage compartment floor cover. Release the clips and the luggage compartment side trim panel...

    Other information:

    Lincoln Aviator 2020-2024 Service Manual: Removal and Installation - Air Cleaner


    Removal NOTICE: The turbocharger compressor vanes can be damaged by even the smallest particles. When removing any turbocharger or engine air intake system component, ensure that no debris enters the system. Failure to do so may result in damage to the turbocharger...

    Lincoln Aviator 2020-2024 Owners Manual: About SYNC


    The system allows you to interact with the entertainment, information and communication systems on your vehicle using voice commands and a touchscreen. The system provides easy interaction with audio, phone, navigation, mobile apps and settings...

    Categories

    Emergency Locking

    Each door has a backup power system which allows the door to function if your vehicle has no power. The system has a limited number of operations before the power is depleted and turns off. When the system turns off, the door remains open and unlatched and does not close.

    If your vehicle has no power and the backup power system is turned off, you can close and secure your vehicle by manually resetting each door latch using a key in the position shown.

    read more

     
    Copyright © 2024 www.liaviator2.com