Lincoln Aviator: Lane Keeping System / Description and Operation - Lane Keeping System - Component Location
Component Location - Lane Keeping System
Item |
Description |
1 |
IPMA
|
2 |
Lane Keeping System (LKS) switch (integral to the LH steering column multifunction switch)
|
Overview
The
Lane Keeping System (LKS) has 2 functions, lane keeping aid and lane
keeping alert. The Lane Keeping System (LKS) utilizes the camera located
in the IPMA to detect
and track the road lane markings...
Other information:
Diagnostic Trouble Code (DTC) Chart
Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods (100-00 General Information, Description and Operation).
Diagnostic Trouble Code Chart
Module
DTC
Description
Action
BCM
B11DB:02
Battery Monitoring Module "A": General Signal Failure
GO to Pinpoint Test F
BCM
B11DB:08
Battery Monitoring Module "A": Bus Signal/Message Failures
GO to Pinpoint Test F
BCM
B11DB:09
Battery Monitoring Module "A": Component Failures
GO to Pinpoint Test F
BCM
B11DB:11
Battery Monitoring Module "A": Circuit Short To Ground
GO to Pinpoint Test F
BCM
B11DB:49
Battery Monitoring Module "A": Internal Electronic Failure
GO to Pinpoint Test I
BCM
B11DB:55
Battery Monitoring Module "A": Not Configured
GO to Pinpoint Test J
BCM
B1489:11
Battery Monitoring System (BMS) Sensor Power: Circuit Short To Ground
GO to Pinpoint Test F
PCM
P0562:00
System Voltage Low: No Sub Type Information
GO to Pinpoint Test B
PCM
P0563:00
System Voltage High: No Sub Type Information
GO to Pinpoint Test A
PCM
P065B:00
Generator "A" Control Circuit Range/Performance: No Sub Type Information
GO to Pinpoint Test B
PCM
P065C:00
Generator "A" Mechanical Performance: No Sub Type Information
GO to Pinpoint Test B
PCM
P0A3B:00
Generator "A" Over Temperature: No Sub Type Information
GO to Pinpoint Test K
PCM
P0A5A:00
Generator Current Sensor Circuit Range/Performance: No Sub Type Information
GO to Pinpoint Test E
PCM
P0A5B:00
Generator Current Sensor Circuit Low: No Sub Type Information
GO to Pinpoint Test E
PCM
P0A5C:00
Generator Current Sensor Circuit High: No Sub Type Information
GO to Pinpoint Test E
PCM
U012D:00
Lost Communication With Generator "A" Control Module: No Sub Type Information
GO to Pinpoint Test G
PCM
U042E:00
Invalid Data Received From Generator "A" Control Module: No Sub Type Information
GO to Pinpoint Test G
Inspection and Verification
Verify the customer concern by operating the charging system...
Symptom Chart(s)
Preliminary Inspection
Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods (100-00 General Information, Description and Operation).
Before diagnosing or repairing the seatbelt system, inspect the following items:
Seatbelt webbing integrity (torn, frayed, cut or stretched)
Seatbelt buckle and tongue assembly (latching and release, foreign debris)
Symptom Chart: Seatbelt System
Symptom Chart
Condition
Action
The seatbelt warning indicator does not operate
GO to Pinpoint Test A
The seatbelt warning chime does not operate
GO to Pinpoint Test B
The seatbelt retractor webbing does not
extract or exhibits excessive pressure on the occupant during use
GO to Pinpoint Test C
The seatbelt retractor webbing does not retract or has excessive slack during use
GO to Pinpoint Test C
The Belt-Minder® feature is inoperative
GO to Pinpoint Test D
The seatbelt tongue is rotated on the seatbelt webbing
GO to Pinpoint Test E
The seatbelt webbing is twisted at the seatbelt guide
GO to Pinpoint Test E
The seatbelt webbing is dirty or soiled
GO to Pinpoint Test E
Pinpoint Tests
PINPOINT TEST A : THE SEATBELT WARNING INDICATOR DOES NOT OPERATE
Normal Operation and Fault Conditions
Turn the ignition on and monitor the airbag warning indicator after the IPC proves out...