Lincoln Aviator: Seatbelt Systems / General Procedures - Seatbelt Maintenance
Inspection
WARNING:
All seatbelt components must be inspected and corrected as
part of any collision repair. Inspect all seatbelt components as
prescribed by Seatbelt Procedure After a Collision found in Section
501-20A General Procedures of this manual. Failure to follow this
instruction may result in incorrect operation of the seatbelt system and
increase the risk of serious personal injury or death in a crash.
-
Periodically inspect the seatbelt assemblies for damage
and that they remain in correct operating condition, particularly if
they have been subjected to severe stress.
-
Before installing the new seatbelt assembly, inspect the
seatbelt retaining areas for damage and distortion. If the retaining
points are damaged and distorted, work the sheet metal back to its
original shape and structural integrity.
-
Install the new seatbelt(s) using the appropriate
instructions. Carry out the appropriate Functional Test procedure for
all seating positions.
Refer to: Seatbelt Systems (501-20A Seatbelt Systems, Diagnosis and Testing).
Cleaning
WARNING:
Do not bleach or re-dye the seatbelt webbing, as the webbing
may weaken. Failure to follow this instruction may increase the risk of
serious personal injury or death in a crash...
Inspection
WARNING:
All seatbelt components must be inspected and corrected as
part of any collision repair. Inspect all seatbelt components as
prescribed by Seatbelt Procedure After a Collision found in Section
501-20A General Procedures of this manual...
Other information:
Diagnostic Trouble Code (DTC) Chart
Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices.REFER to: Diagnostic Methods (100-00 General Information, Description and Operation).
Diagnostic Trouble Code Chart
Module
DTC
Description
Action
PCM
P0505:00
Idle Control System: No Sub Type Information
GO to Pinpoint Test HU
PCM
P0506:00
Idle Control System - RPM Lower Than Expected: No Sub Type Information
GO to Pinpoint Test HU
PCM
P0507:00
Idle Control System - RPM Higher Than Expected: No Sub Type Information
GO to Pinpoint Test HU
PCM
P050A:00
Cold Start Idle Control System Performance: No Sub Type Information
GO to Pinpoint Test HU
PCM
P050B:00
Cold Start Ignition Timing Performance: No Sub Type Information
GO to Pinpoint Test HU
PCM
P050E:00
Cold Start Engine Exhaust Temperature Too Low: No Sub Type Information
GO to Pinpoint Test HU
PCM
P115E:00
Throttle Actuator Control Throttle Body Air Flow Trim At Max Limit: No Sub Type Information
GO to Pinpoint Test HU
PCM
P1548:00
Engine Air Filter Restriction: No Sub Type Information
GO to Pinpoint Test HU
PCM
P2004:00
Intake Manifold Runner Control Stuck Open (Bank 1): No Sub Type Information
GO to Pinpoint Test HU
PCM
P2005:00
Intake Manifold Runner Control Stuck Open (Bank 2): No Sub Type Information
GO to Pinpoint Test HU
PCM
P2006:00
Intake Manifold Runner Control Stuck Closed (Bank 1): No Sub Type Information
GO to Pinpoint Test HU
PCM
P2007:00
Intake Manifold Runner Control Stuck Closed (Bank 2): No Sub Type Information
GO to Pinpoint Test HU
PCM
P2008:00
Intake Manifold Runner Control Circuit/Open (Bank 1): No Sub Type Information
GO to Pinpoint Test HU
PCM
P2011:00
Intake Manifold Runner Control Circuit/Open (Bank 2): No Sub Type Information
GO to Pinpoint Test HU
PCM
P2014:00
Intake Manifold Runner Position Sensor/Switch Circuit (Bank 1): No Sub Type Information
GO to Pinpoint Test HU
PCM
P2015:00
Intake Manifold Runner Position
Sensor/Switch Circuit Range/Performance (Bank 1): No Sub Type
Information
GO to Pinpoint Test HU
PCM
P2016:00
Intake Manifold Runner Position Sensor/Switch Circuit Low (Bank 1): No Sub Type Information
GO to Pinpoint Test HU
PCM
P2017:00
Intake Manifold Runner Position Sensor/Switch Circuit High (Bank 1): No Sub Type Information
GO to Pinpoint Test HU
PCM
P2019:00
Intake Manifold Runner Position Sensor/Switch Circuit (Bank 2): No Sub Type Information
GO to Pinpoint Test HU
PCM
P2020:00
Intake Manifold Runner Position
Sensor/Switch Circuit Range/Performance (Bank 2): No Sub Type
Information
GO to Pinpoint Test HU
PCM
P2021:00
Intake Manifold Runner Position Sensor/Switch Circuit Low (Bank 2): No Sub Type Information
GO to Pinpoint Test HU
PCM
P2022:00
Intake Manifold Runner Position Sensor/Switch Circuit High (Bank 2): No Sub Type Information
GO to Pinpoint Test HU
Global Customer Symptom Code (GCSC) Chart
Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices...
Overview
The power liftgate feature allows power opening and closing of the liftgate using any of the following methods:
The front power liftgate switch (located on the instrument panel).
The rear interior power liftgate switch (located on the bottom of the liftgate trim panel) (close only)...