Lincoln Aviator Manuals
Lincoln Aviator 2020-2025 Service Manual / Powertrain / Automatic Transmission / Automatic Transmission - 10-Speed Automatic Transmission – 10R60 / Diagnosis and Testing - C Clutch

Lincoln Aviator: Automatic Transmission - 10-Speed Automatic Transmission – 10R60 / Diagnosis and Testing - C Clutch

Symptom Chart

C Clutch

For C clutch operation,
REFER to: C Clutch (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Description and Operation).


  C Clutch


Condition Possible Sources Action
C clutch does not apply SSC mechanically stuck OFF INSTALL a new solenoid.
REFER to: Shift Solenoids (SS) (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Removal and Installation).
C clutch control valve stuck OFF DISASSEMBLE, CLEAN and INSPECT the C clutch control valve. If the bore or valve is damaged, INSTALL a new main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Removal and Installation).
C clutch latch valve stuck OFF DISASSEMBLE, CLEAN and INSPECT the C clutch latch valve. If the bore or valve is damaged, INSTALL a new main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Removal and Installation).
C clutch hydraulic circuit blocked/leaking DISASSEMBLE and INSPECT the main control valve body and separator plate passages for debris, blockage and leaks. CLEAN as necessary.
REFER to: Main Control Valve Body (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Removal and Installation).
CARRY OUT the air pressure test on the C clutch.
REFER to: Special Testing Procedures (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Diagnosis and Testing).
If a leak is detected, INSPECT the front support assembly, input shaft Teflon seals, CDF clutch cylinder and C clutch piston seals for leaks. INSTALL new components as necessary. REFER to: Transmission (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Overhaul).
CDF clutch cylinder, ring gear no. 2, sun gear no.3 DISASSEMBLE and INSPECT the CDF clutch cylinder, ring gear no. 2 and sun gear no. 3 for wear and damage. INSTALL new components as necessary.
REFER to: Transmission (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Overhaul).
C clutch piston seals DISASSEMBLE and INSPECT the C clutch piston seals for wear and damage. INSTALL new components as necessary.
REFER to: Transmission (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Overhaul).
C clutch friction plates DISASSEMBLE and INSPECT the C clutch friction and steel plates for wear and damage. INSTALL new components as necessary.
REFER to: Transmission (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Overhaul).
C clutch always applied SSC mechanically stuck ON INSTALL a new solenoid.
REFER to: Shift Solenoids (SS) (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Removal and Installation).
C clutch control valve stuck ON DISASSEMBLE, CLEAN and INSPECT the C clutch control valve. If the bore or valve is damaged, INSTALL a new main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Removal and Installation).
C clutch latch valve stuck ON DISASSEMBLE, CLEAN and INSPECT the C clutch latch valve. If the bore or valve is damaged, INSTALL a new main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Removal and Installation).
C clutch hydraulic circuit cross leaks DISASSEMBLE and INSPECT the main control valve body and separator plate passages for cracks, warping and damage. If damage is found, INSTALL a new main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Removal and Installation).
CDF clutch cylinder, ring gear no. 2 DISASSEMBLE and INSPECT the components for wear and damage. INSTALL new components as necessary.
REFER to: Transmission (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Overhaul).
C clutch piston return spring DISASSEMBLE and INSPECT the C clutch piston return spring for damage. INSTALL new components as necessary.
REFER to: Transmission (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Overhaul).
C clutch friction plates DISASSEMBLE and INSPECT the C clutch friction and steel plates for wear and damage. INSTALL new components as necessary.
REFER to: Transmission (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Overhaul).
C clutch delayed/soft/slipping apply Incorrect transmission strategy programmed into PCM/ TCM. CARRY OUT the Transmission Strategy Download and the Adaptive Learning Drive Cycle.
REFER to: Transmission Strategy Download (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, General Procedures).
REFER to: Adaptive Learning Drive Cycle (307-01B Automatic Transmission - 10-Speed Automatic Transmission – 10R80 MHT, General Procedures).
Low line pressure CARRY OUT the line pressure test. If line pressure is low, REFER to the Line Pressure Diagnosis Chart.
REFER to: Special Testing Procedures (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Diagnosis and Testing).
SSC mechanically sticking
  • If the vehicle has less than 5,000 miles (8,000 km), CARRY OUT the PCM - Transmission Accelerated Main Control Break In routine 3 times using the diagnostic scan tool.
  • For all other vehicles, INSTALL a new solenoid.
    REFER to: Shift Solenoids (SS) (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Removal and Installation).
C clutch control valve sticking
  • If the vehicle has less than 5,000 miles (8,000 km), CARRY OUT the PCM - Transmission Accelerated Main Control Break In routine 3 times using the diagnostic scan tool.
  • For all other vehicles, DISASSEMBLE, CLEAN and INSPECT the C clutch control valve. If the bore or valve is damaged, INSTALL a new main control valve body.
    REFER to: Main Control Valve Body (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Removal and Installation).
C clutch latch valve sticking
  • If the vehicle has less than 5,000 miles (8,000 km), CARRY OUT the PCM - Transmission Accelerated Main Control Break In routine 3 times using the diagnostic scan tool.
  • For all other vehicles, DISASSEMBLE, CLEAN and INSPECT the C clutch latch valve. If the bore or valve is damaged, INSTALL a new main control valve body.
    REFER to: Main Control Valve Body (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Removal and Installation).
C clutch hydraulic circuits blocked/leaking DISASSEMBLE and INSPECT the main control valve body and separator plate passages for debris, blockage and leaks. CLEAN as necessary.
REFER to: Main Control Valve Body (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Removal and Installation).
CARRY OUT the air pressure test on the C clutch.
REFER to: Special Testing Procedures (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Diagnosis and Testing).
If a leak is detected, INSPECT the front support assembly, input shaft Teflon seals, CDF clutch cylinder and C clutch piston seals for leaks. INSTALL new components as necessary. REFER to: Transmission (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Overhaul).
C clutch piston seals DISASSEMBLE and INSPECT the C clutch piston seals for wear and damage. INSTALL new components as necessary.
REFER to: Transmission (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Overhaul).
C clutch friction plates DISASSEMBLE and INSPECT the C clutch friction and steel plates for wear and damage. INSTALL new components as necessary.
REFER to: Transmission (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Overhaul).
C clutch harsh apply Incorrect transmission strategy programmed into PCM/ TCM. CARRY OUT the Transmission Strategy Download and the Adaptive Learning Drive Cycle.
REFER to: Transmission Strategy Download (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, General Procedures).
REFER to: Adaptive Learning Drive Cycle (307-01B Automatic Transmission - 10-Speed Automatic Transmission – 10R80 MHT, General Procedures).
High line pressure CARRY OUT the line pressure test. If line pressure is high, REFER to the Line Pressure Diagnosis Chart.
REFER to: Special Testing Procedures (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Diagnosis and Testing).
SSC mechanically sticking
  • If the vehicle has less than 5,000 miles (8,000 km), CARRY OUT the PCM - Transmission Accelerated Main Control Break In routine 3 times using the diagnostic scan tool.
  • For all other vehicles, INSTALL a new solenoid.
    REFER to: Shift Solenoids (SS) (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Removal and Installation).
C clutch control valve sticking
  • If the vehicle has less than 5,000 miles (8,000 km), CARRY OUT the PCM - Transmission Accelerated Main Control Break In routine 3 times using the diagnostic scan tool.
  • For all other vehicles, DISASSEMBLE, CLEAN and INSPECT the C clutch control valve. If the bore or valve is damaged, INSTALL a new main control valve body.
    REFER to: Main Control Valve Body (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Removal and Installation).
C clutch latch valve sticking
  • If the vehicle has less than 5,000 miles (8,000 km), CARRY OUT the PCM - Transmission Accelerated Main Control Break In routine 3 times using the diagnostic scan tool.
  • For all other vehicles, DISASSEMBLE, CLEAN and INSPECT the C clutch control valve. If the bore or valve is damaged, INSTALL a new main control valve body.
    REFER to: Main Control Valve Body (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Removal and Installation).
C clutch hydraulic circuit blocked/leaking DISASSEMBLE and INSPECT the main control valve body and separator plate passages for debris, blockage and leaks. CLEAN as necessary.
REFER to: Main Control Valve Body (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Removal and Installation).
C clutch piston return spring DISASSEMBLE and INSPECT the C clutch piston return spring for damage. INSTALL new components as necessary.
REFER to: Transmission (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Overhaul).
C clutch friction plates DISASSEMBLE and INSPECT the C clutch friction and steel plates for wear and damage. INSTALL new components as necessary.
REFER to: Transmission (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Overhaul).

    Diagnosis and Testing - B Clutch

    Symptom Chart B Clutch For B clutch operation, REFER to: B Clutch (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Description and Operation)...

    Diagnosis and Testing - D Clutch

    Symptom Chart D Clutch For D clutch operation, REFER to: D Clutch (307-01A Automatic Transmission - 10-Speed Automatic Transmission – 10R60, Description and Operation)...

    Other information:

    Lincoln Aviator 2020-2025 Service Manual: Removal and Installation - Roof Panel


    Special Tool(s) / General Equipment Resistance Spotwelding Equipment Scraper for Straight Edges Hot Air Gun Knife 8 mm Drill Bit MIG/MAG Welding Equipment Spot Weld Drill Bit Locking Pliers Materials Name Specification Metal Bonding AdhesiveTA-1, TA-1-B, 3M™ 08115, LORD Fusor® 108B -  Seam SealerTA-2-B, 3M™ 08308, LORD Fusor® 803DTM -  Removal   WARNING: Before beginning any service procedure in this manual, refer to health and safety warnings in section 100-00 General Information...

    Lincoln Aviator 2020-2025 Service Manual: Description and Operation - Wireless Accessory Charging Module (WACM) - System Operation and Component Description


    System Operation System Diagram Item Description 1 APIM 2 BCM 3 ACM 4 WACM 5 GWM Network Message Chart   APIM Module Network Input Messages Broadcast Message Originating Module Message Purpose WACM send signals   WACM Contains the status of the WACM charging input to be used for FCIM display...

    Categories

    Adjusting the Steering Wheel - Vehicles With: Manual Adjustable Steering Column

    WARNING: Do not adjust the steering wheel when your vehicle is moving.

    Note: Make sure that you are sitting in the correct position.

    Unlock the steering column. Adjust the steering wheel to the desired position.

    Lincoln Aviator. Column

    Lock the steering column.

    read more

     
    Copyright © 2025 www.liaviator2.com